Auto-meter 3810 Manuale Utente Scaricare il pdf

12V BATTERY

INSTALLATION INSTRUCTIONS

FULL SWEEP

ELECTRIC FUEL LEVEL

2650-1136

1. Check that you have all parts required for installation, and that the engine is cool.

2. Disconnect the negative (-) battery cable.

3. Gauge mounts in a 2

⁄

” hole for 2

⁄

” gauges, and a 2

⁄

” hole for 2

⁄

” gauges.

4. Connect the purple sender wire to the fuel level sender. Existing wires may be used, or route the

purple sender wire to the fuel tank.

(The stock fuel level gauge, if equipped, must be disconnected.)

5. Connect the white wire to dash lighting or switchable 12v light source.

6. Connect one of the black wires to a good ground. (Either black wire, does not matter which one)

7. Connect the red power wire to a switched +12v source.

8. Reconnect the negative (-) battery cable.

1. The brown and black wires are used to set the sender type. The gauge ships pre-programmed to read GM 0-90 ohm senders.

If using a 0-90 ohm GM sender, separately insulate the ends of the brown and black wires with electrical tape, and coil them up

under the dash.

2. If any other sender type is required, connect a Radio Shack 275-1556 or equivalent momentary switch to the black and brown

wires (see illustration above), or alternately touch the stripped ends of the black and brown wires to simulate pushing the button.

3. Press and hold the button, and apply power to the gauge. The pointer will sweep back and forth stopping momentarily on each

⁄

-tank mark, indicating that the gauge is in sender select mode.

4. Allow the pointer to move to the appropriate location on the dial per the sender select chart (see next page), and release the

pushbutton. The pointer can be bumped to the next position by momentarily pressing the button.

5. Remove power from the gauge to store the new sender type by turning off ignition switch.

6. Re-apply power to the gauge, and confirm that it reads the proper fuel level. If the proper fuel level is not read, return to step 3

and recalibrate. If the proper fuel level is still not indicated, perform Custom Sender Calibration.

7. Remove power from the gauge by turning off ignition switch.

8. Remove switch if used, and tape the ends of the brown and black wires, so they can not touch.

9. Coil the wires up under the dash.

Setting the Sender Type

Installation

GOOD ENGINE

GROUND

+ 12V CONNECTION

RED

BLACK

+ 12V DASH LIGHTING

FOR THRU-DIAL LIT GAUGES ONLY

(NOT USED ON GAUGES THAT ACCEPT

INCANDESCENT BULB FOR LIGHTING)

CONNECT TO FUEL LEVEL

SENDER (MAKE SURE

SENDER IS GROUNDED)

WHITE

PURPLE

FUSE

(SEE CAUTION LEFT)

BLACK

BROWN

RADIO SHACK 275-1556

(OPTIONAL)

CAUTION!

As a safety precaution, the +12V terminal

of this product should be fused before

connecting to the 12V ignition switch. We

recommend using a 1 Amp, 3AG fast-

acting type cartridge fuse (Littlefuse

recommend using a 1 Amp, 3AG fast-

#312 001 or an equivalent).

CONNECT TO

12V LIGHTING

CONNECT

TO GOOD GROUND

FOR INCANDESCENT BACKLIT

GAUGES ONLY

LIGHT

QUESTIONS

If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s),

please contact Auto Meter Technical Service at

815-899-0801.

You may also email us at

[email protected].

Additional information can also be found at

http://www.autometer.com

1 2

Sommario

Pagina 1 - ELECTRIC FUEL LEVEL

12V BATTERYINSTALLATION INSTRUCTIONSFULL SWEEP ELECTRIC FUEL LEVEL2650-11361. Check that you have all parts required for installation, and that the en

Pagina 2 - 12 MONTH LIMITED WARRANTY

12 MONTH LIMITED WARRANTYAuto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in

Modelli collegati 5910 | 8010 | 1109 |

Commenti su questo manuale

Nessun commento

Auto-meter 3810 Manuale Utente

Navigare online o scaricare Manuale Utente per Per l'auto Auto-meter 3810. Auto Meter 3810 User Manual Manuale Utente

Sommario

Modelli collegati 5910 | 8010 | 1109 |

Commenti su questo manuale

Prodotti e manuali riguardandi Per l'auto Auto-meter 3810