Auto-meter 4381 Manuale Utente Scaricare il pdf

INSTALLATION INSTRUCTIONS

2650-1706-00

WARNING!

The installation of the Auto Meter Boost Controller is recommended only for experienced technicians. This product may damage your engine if used properly or

improperly. Use extreme caution during installation and operation. When increasing boost, it is recommended to carefully increase the pressure in small intervals to avoid

engine damage. Auto Meter Products is not responsible for any engine damage caused by improper installation or the use of this product.

The Auto Meter Boost Controller is intended for off-road use only.

WIRING INSTALLATION

BOOST CONTROLLER

Red Wire (Power):

Connect to a switched +12 volt source.

Black Wire (Ground):

Connect to good engine ground.

White Wire (Lighting Power)

Connect to dash lighting power.

Green Wire (Optional Tach Signal)*

Connect to the negative terminal of a standard ignition coil, or to the "Tach Output" terminal on the electronic ignition module. (See Tach

Signal section for further details)

Violet Wire (Optional Speed Signal)**

Connect to vehicle speed signal. (See Speed Signal section for further details)

Blue Wire (Optional Data Logger Signal Output)***

Connect to signal input(+) or Engine Management System or Data Acquisition unit.

Black/White Wire (Optional*** Data Logger Signal Ground)***

Connect to signal input(-) on Engine Management system or Data Acquisition Unit.

Orange (Optional Pro Control Output)****

Ground trigger for auxiliary device. Maximum 2 amps at 12 volts. (See Pro Control section for further details)

Black/White Wire (Optional Pro Control Ground)****

Connect to a good ground only when Pro Control is used. Pro Control ground reference point. (See Pro Control section for further details)

Gray Wire (Optional Pro Control Ground)****

Grounding this will shut down the Boost Control Valve. This can connect the pro control output to another gauge.

* Only used if Boost by RPM or Boost by Gear is used

** Only used if Boost by Gear is used

*** Only used if vehicle is equipped with a data logger or PCM that can utilize the signal

**** Only used if Pro Control is desired to control an auxiliary electronic device

12V BATTERY

Data Logger and

Pro Control Ground

Data Logger

Output

Speed

Signal

Tach

Signal

Pro Control Input

(Optional)

Pro Control

Out

Black/White

Blue

Violet

Green

Orange

Gray

Black

White

+12v Connection

*See step 8 below

Good Engine

Ground

+12v

Dash

Lighting

Boost Control

Valve

Fuse

(see

caution

below)

Red

Compression

Adapter

Compression

Nut

Tubing Adapter

Nylon

Tubing

Pressure Port

Map Sensor (see note)

Ferrule

Vacuum “T”

NOTE: MAP Sensor should be mounted with

PRESSURE PORT facing down.

Failure to do so could result in

inaccurate readings due to

condensation in the line.

(Bracket fabrication may be required.)

WARNING!

Warranty will be void if connected to coil when using an aftermarket ignition box such as, but not limited to

products from the following manufacturers: MSD, Crane, Jacobs, Mallory, Holley, Etc.. Prior to installation of

your boost controller, check with the ignition box manufacturer for recommended tachometer signal location.

CAUTION!

As a safety precaution, the +12V terminal of this

product should be fused before connecting to the

12V ignition switch. We recommend using a 3 AMP

automotive type fuse.

1 2 3 4 5 6 7

Sommario

Pagina 1 - BOOST CONTROLLER

INSTALLATION INSTRUCTIONS2650-1706-00®WARNING!The installation of the Auto Meter Boost Controller is recommended only for experienced technicians. Thi

Pagina 2 - BOOST SOLENOID INSTALLATION

Connect the tach signal to the negative side of the coil* when using a standard ignition. HEI ignition systems will provide a tach signal terminal off

Pagina 3

Port 1 – To turbo pressure source, shared with bottom port if the wastegatePort 2 – To both wastegatesPort 3 – Sintered mufﬂerThis set up is used whe

Pagina 4

Port 1 – Sintered mufﬂerPort 2 – To bottom port on both wastegatesPort 3 – To turbo pressure sourcePort 1 – To turbo pressure source, shared with bott

Pagina 5 - DUTY CYCLE SETTING ( )

This product has many features that can be adjusted for your speciﬁc application. Use the MODE (-), HI/LO, and SELECT (+) buttons to navigate menu opt

Pagina 6 - PRESSURE UNITS ( )

This sets the boost pressure level that causes the led bar graph to reach its maximum. At this level, all the green leds will be lit. If the boost lev

Pagina 7 - DATA LOGGER OUTPUT ( )

FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (866) 248-6357Email us at [email protected] SERVICEFor se

Modelli collegati 2681 | 5782 | 6181 |

Commenti su questo manuale

Nessun commento

Auto-meter 4381 Manuale Utente

Navigare online o scaricare Manuale Utente per Per l'auto Auto-meter 4381. Auto Meter 4381 User Manual Manuale Utente

Sommario

Modelli collegati 2681 | 5782 | 6181 |

Commenti su questo manuale

Prodotti e manuali riguardandi Per l'auto Auto-meter 4381