Auto-meter 1110 Manuale Utente Scaricare il pdf

OIL

FUEL

WATER

+12V

GND

LAMP

Do not touch ignition wire to the sender terminal on

back of gauge or the sender will be damaged.

CAUTION:

INSTALLATION INSTRUCTIONS

⁄8" & 5" ELECTRIC QUAD GAUGES

2650-1178

Mounting

Mount a 3

⁄8" gauge in a 3

⁄8" dia. hole and a 5" gauge in

⁄8" dia. hole in the dashboard. Fasten with brackets supplied

as shown. (Electrical wire for installation not included.)

To assure proper functioning of this instrument, please read

instructions thoroughly before installing.

1. Gauge connects to 240-33 ohm fuel sender

(3262), supplied in Quad gauge/Speedometer

kit. Sender is not included in individual Quad

gauges. The 3262 or comparable 240-33 ohm

sender will be required. Route proper length

of 18 gauge wire from fuel tank to gauge.

Connect one end to terminal post on fuel level

sender and the opposite end to the spade ter-

minal labeled “FUEL” on back of gauge. See

illustration.

Voltmeter

1. Using 18 gauge wire, route wire through firewall using

grommet. Attach one end to the negative GND (-)

spade terminal on back of gauge, and the opposite

end to a good engine ground. See illustration at right.

2. Attach one length of wire to the positive +12V spade

terminal on back of gauge and opposite end to +12V

terminal on ignition switch or other switched +12V

power source.

To 12V Terminal on Ignition

Switch or other 12V source.

Step 1

1. Disconnect negative (-) battery cable.

Step 2

Fuel Level

Step 3

Do not touch ignition wire to the sender terminal on

back of gauge or the sender will be damaged.

CAUTION:

PASSED

MODEL NUMBER

DATE OF MANUFACTURE

OIL

FUEL

WATER

+12V

GND

LAMP

Connect to terminal post

on fuel tank sender.

Grommet

Ground

5" Models

⁄16"

⁄8"

⁄32"

Grommet

CAUTION!

As a safety precaution the Red wire of this product should

be fused before connecting it to the positive (+) side of

the 12V DC battery. We recommend using a 4 Amp, 3AG

fast-acting type cartridge fuse (Littlefuse

# 312 004 or

an equivalent) inline with the Red wire of our product.

⁄8" Models

⁄32"

⁄4"

5" Models

⁄8" Models

NOTE: Some late model vehicles use electronic sensors in their

pressure and temperature senders for engine control func-

tions. Before removing the original sender, we recommend

that you contact your automotive dealer to be sure no

critical functions will be disrupted. With pressure gauges

it is beneficial to add a T-fitting to install your new gauge

and to keep the warning light operational. This allows you

to monitor the pressure and still have a warning light to

indicate emergency conditions. The ground, fuel sender,

temperature sender, and oil sender wires should be routed

through fire wall using the supplied grommet.

QUESTIONS:

If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s),

please contact Auto Meter Technical Service at 815-899-0801. You may also email us at [email protected].

Additional information can also be found at http://www.autometer.com

1 2

Sommario

Pagina 1 - CAUTION!

OILFUELWATER+12VGNDLAMPDo not touch ignition wire to the sender terminal on back of gauge or the sender will be damaged.CAUTION:INSTALLATION INSTRUCTI

Pagina 2 - " models only)

FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815)899-0801 orEmail us at [email protected] MONTH LIMITED

Commenti su questo manuale

Nessun commento

Auto-meter 1110 Manuale Utente

Navigare online o scaricare Manuale Utente per Per l'auto Auto-meter 1110. Auto Meter 1110 User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Per l'auto Auto-meter 1110