Auto-meter 2895 Manuale Utente Scaricare il pdf (Pagina 1)

2650-1139

QUESTIONS:

If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s),

please contact Auto Meter Technical Service at 815-899-0801.

You may also email us at service@autometer.com.

Additional information can also be found at http://www.autometer.com/tech_faq.aspx

Calibration

IMPORTANT: This tachometer is factory calibrated to

operate on 8 cylinder engines. For 4 or

6 cylinder engines, it is necessary to

make the proper adjustments to adapt

this tachometer to your cylinder range.

NOTE: Calibration changes do not apply to the Jr. Dragster

tachometer. The Jr. Dragster tachometer is calibrated

to operate only on Briggs & Stratton engines.

Figure B.

4 CYL. - Switch One up, Switch Two down

6 CYL. - Switch One down, Switch Two up

8 CYL. - Both switches up

If you are unsure of your vehicle’s pulse(s) per revolution

or specic calibration requirements, contact Auto Meter

Technical Service Dept. at (815) 899-0801, or go to

www.autometer.com/hp/tectips for information.

Switch is not visible

from from this angle,

shown for location only.

Access switch

through

light hole.

(Angle view through access hole)

Figure B

1 2

4 CYL. / 2 PULSE

6 CYL. / 3 PULSE 8 CYL. / 4 PULSE

UP DN

DN UP UP UP

To change the tachometer calibration, access to the inner case

is necessary. Remove the two acorn nuts as shown in gure A

and carefully slide the cup of the tachometer back in order to

access the inner case. Locate the switch access hole on the inner

case. Remove twist-lock light socket to access the calibration

switches. (See light replacement) Use a small screwdriver or an

unwound paper clip to change the switch settings. Move each of

the two switches to the proper cylinder selection according to the

diagram illustrated on the right.

NOTE: This tachometer has an air core meter. With power off,

It is normal for the pointer to leave zero. When power

is applied, the pointer will move to the correct position.

Figure A

Acorn

Nuts

Twist In

light

Figure C

Mounting

Light Replacement

" SIZE

SHOWN

The special design of the tachometer base allows for a variety of mounting possibilities.

Loosening the hex screws at the mounting base allows the tachometer to be rotated in

the strap. Also, this design allows the tachometer face to be angled forward or backward

for better viewing. Attach the base using screws provided or some other fasteners.

See gure C. Rotate twist-lock socket counterclockwise using needle nose pliers and remove.

Replace old bulb with GE 194 bulb.

INSTALLATION INSTRUCTIONS

TACHOMETER

1 2

Sommario

Pagina 1 - TACHOMETER

2650-1139QUESTIONS:If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s),ple

Pagina 2 - Jr. Dragster Wiring

SERVICE For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along

Modelli collegati 2894

Commenti su questo manuale

Nessun commento

Auto-meter 2895 Manuale Utente Pagina 1

Navigare online o scaricare Manuale Utente per Per l'auto Auto-meter 2895. Auto Meter 2895 User Manual Manuale Utente

Sommario

Modelli collegati 2894

Commenti su questo manuale

Auto-meter 2895 Manuale Utente Pagina 1

Navigare online o scaricare Manuale Utente per Per l'auto Auto-meter 2895. Auto Meter 2895 User Manual Manuale Utente

Sommario

Modelli collegati 2894

Commenti su questo manuale

Prodotti e manuali riguardandi Per l'auto Auto-meter 2895